when i plug in usb there are two options available
1. External Usb Hard drive
2. Usb Hard drive1 — usb flash disk
when i boot from 1.External Usb Hard drive
a graphical screen shows up with drives and a drive «Boot from macOS sierra» and a drive boot from «Clover»
when i press on macOS Sierra it says «Boot failed: sleeping for 10 seconds before exiting»
and when i press boot from clover it hangs
when i boot from 2.Usb Hard drive 1 — usb flash disk
a non-graphical screen shows up there drivers are written in format (0,0) drive name
there when i boot from macOS Sierra setup starts successfully after selecting language accepting license when i go to disk utility there is only 1 option internal hard drive and it has only a usb which i’ve connected…my HARD DRIVES ARE NOT SHOWING IN disk utility!!!
:blush:Hi All,
I am new to Hackintosh. But I did find my way here. My computer spec is the Dell T3600 server
it has Intel Xeon E5-2667 CPU, nVidia Quadro 600, and ALC269 sound card
I downloaded an iso and created a bootable usb stick. It loaded with Clover Bootloader 2953.
However, i didn’t able to install without Safe mode, it will give me the follow
…………….Error alocating 0x800 pages at 0x000000000014e000000 alloc type 2
Error Loading kernel cache (0x9)
Boot failed, sleeping for 10 seconds before exiting…
So I installed Yosemite using safe mode.
The install went through without problem.
However, when I try to boot the system, it said it doesn’t have a bootloader. So I plugged back in the bootable usb stick for the Clover bootloader and tried to boot into Yosemite.
It gives me above error again if I don’t use safe mode. So I booted with safe mode again.
It stayed at the black screen with a mouse cursor for around 20 mins, Then it goes to the login screen. I type in the password, and have to wait for another 3 mins before it moves again. Then the screen refresh very slowly and finally got into the system.
Once I got into the system, it works with normal speed, but the network card and sound card doesn’t work.
I used [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url] to install the drivers. The network works immediately, but sound doesn’t. I notice the graphics is snugglish sometimes with artifacts so I downloaded and installed the official Yosemite driver from nVidia (but I dont’ know if it has nVidia Quadro 600 driver) However that didn’t help the graphics, I believe the driver for the graphics wasn’t loaded.
Is it because I boot with safe mode that why the sound driver and video card driver weren’t loaded?
Thanks,
bchiu
BTW, I installed Yosemite on an external usb hd. I am not sure if that is related to the problem.
Boot Loop after Vanilla 10.13.1 Install
Hello all,
I used the Hackintosher guide for a vanilla High Sierra install, which worked great on the first try, I got through the initial install, edited the XML to keep HFS+, and finished the full install. Upon rebooting after the full install finished, I get a boot loop- I can’t even get Clover to boot back into the installer again… All three clover entries (USB installer / MacOS drive / Recovery) result in the same error: It looks like I’m halting with the following:
-
Error allocating 0x11aa6 pages at…
-
Couldn’t allocate runtime area
-
Boot failed, sleeping for 10 seconds before exiting…
First, I believe this is an error related to RAM- which I know happens from time to time without ECC RAM, but I’ve tried probably 30 times now with no luck. Second, I’m not sure why I can’t even get the clover install option to even work this time.
I haven’t done any system modifications post install, so I don’t believe it would be related to the gfx card, but I could be wrong?
Any suggestions? I’m getting pretty frustrated as I spent days going down the Tonymacx86 route with no luck, and I was pleasantly surprised when this installed without a hitch… I guess that was premature.
Guide I used here.
I’ve confirmed my hardware is compatible (had to replace the mobo and gfx before beginning) System Info: MSI X99s SLI PLus, i7-5820k, EVGA GTX-1070, Intel SSD
Thanks for your help!
Edit: The only deviation I made from the guide was to use a config.plist I found for Haswell-E/X99 since they only provided one for the original Haswell and I wasn’t sure it’d be compatible.
<key>PciRoot(0x0)/Pci(0x1F,0x3)</key>
<dict>
<key>AAPL,slot-name</key>
<string>Internal@0,31,3</string>
<key>device_type</key>
<string>Audio device</string>
<key>hda-gfx</key>
<string>onboard-1</string>
<key>model</key>
<string>Cannon Lake PCH cAVS</string>
</dict>
<key>PciRoot(0x0)/Pci(0x2,0x0)</key>
<dict>
<key>AAPL,ig-platform-id</key>
<data>BwCbPg==</data>
<key>AAPL,slot-name</key>
<string>Internal@0,2,0</string>
<key>device-id</key>
<data>kj4AAA==</data>
<key>device_type</key>
<string>VGA compatible controller</string>
<key>enable-hdmi20</key>
<data>AQAAAA==</data>
<key>framebuffer-patch-enable</key>
<data>AQAAAA==</data>
<key>framebuffer-stolenmem</key>
<data>AAAwAQ==</data>
<key>framebuffer-unifiedmem</key>
<data>AAAAgA==</data>
<key>hda-gfx</key>
<string>onboard-1</string>
<key>model</key>
<string>Intel UHD Graphics 630 (Desktop)</string>
</dict>
hi, i’m new here, and i’m very interested in hackintosh.
today i followed this tutorial to try to virtualize macos 10.15 catalina in vmware workspace 15.5.6, but this error appears seconds after the apple logo appears. I’ve tried to update the tools, I’ve tried changing the configuration file; I even restarted my real machine to see if it worked, and nothing, always the same error. I’ve tried finding it on forums, and even on the subreddit, but none of them were the same as mine.
yes, i already tried to do the trick of changing the machine for windows 10 x64 / other 64-bit
yes, i used the unlocker properly
yes, i already tried to increase my virtual ram
note: my processor is an amd a6-9500 dual core 3.50ghz with integrated amd radeon r5 card
submitted by /u/RetroGamerCX
[link] [comments] 